Faber No Oil: How to Remove Grease and Oil Stains

Faber No Oil oil stain remover grease stain remover best oil stain remover how to remove grease stains
Around your house, you will find oil and grease being used everywhere you look; whether it is in the bathroom, kitchen or garage. The same is true of commercial and industrial properties. Despite how commonly oil and grease is used, we still haven’t found the best way to get rid of the stains left behind, until now... until Faber No Oil.

In this article, I will tell you everything you need to know about removing grease and oil stains from a range of stone surfaces. 

What will you need?

Firstly, you need Faber No Oil.  It is the best solvent-based oil and grease stain remover for a wide range of surfaces. 

It is an independent solution and boosts its stain-extracting action, offering top-quality efficiency in stain removal. 

This grease stain removal solution is both easy-to-use and fasting acting. 

You will also need a clean cloth, clean water, a mop,  a spatula and a brush. 

What surfaces are suitable for this treatment?

Due to its special formula, Faber No Oil is ready for use on a wide variety of surfaces without altering their appearance, even the most delicate types such as polished marble. 

This oil stain remover is appropriate for use on acid-sensitive finishes without affecting them or making them lose their shine. 

Suitable for Use On:
- Agglomerate cement-marble
- Agglomerate resin-marble
- Basaltina - Lava  Stone
- Agglomerate resin-quartz
- Brick Facings
- Cement tile
- Ceramic Craquele
- Ceramic Glazed
- Clinker
- Concrete
- Cotto
- Granite
- Limestone
- Manufactured Stone (Eco Stone)
- Marble
- Molted basalt
- Porcelain gres Honed
- Porcelain gres Lappato
- Parquet / Natural Wood
- Porcelain Natural or Structures
- Porphyry
- Quartzite
- Sandstone
- Slate
- Terracotta
- Travertine
- Tuff

Additionally, Faber No Oil is suitable for vertical surfaces. 

How to remove grease stains from stone surfaces?

1. Completely clean and dry surfaces 

Before applying Faber No oil, ensure surfaces are completely clean. Remove any dust, dirt and debris. 

It is also important to note that surfaces being treated with this grease and oil remover should not be wet or more than slightly damp.

2. Apply Faber No Oil

Pour the oil stain remover directly onto the surface. Use a brush or spatula to make sure the surface is completely covered in a thick layer of No Oil. 

3. Leave No Oil to act

Allow for the product to act on the surface until it completely dries.

This oil stain remover becomes a white powdery residue when drying. As a fast drying solution, it dries after no longer than 1-2 hours from application.

4. Remove any residue 

Afterwards, remove any remaining solution and residue with a clean cloth. 

When completely dry, remove the powder residue with a soft bristled broom or clean brush when treating porous materials.

For compact, non absorbent materials, use an absorbent paper, towel or cloth to remove the residue.

Then, wipe the surface with a slight damp cloth or mop and wait for it to dry.  

5. Repeat if necessary 

Repeat this process if the results you want were not achieved. 

Afterwards

For porous surfaces such as sandstand or handmade cotto, after completing the treatment, powder may remain trapped in the pores.

Remove this powder with a vacuum or a liquid cleaner and extractive detergent. We recommend Faber Deterfug.

However, for my difficult cases, use a pressure washer.  

More Information

For more information about grease and oil stain removal, the products mentioned or any products sold by Tiling Logistics don't hesitate to reach out. Never forget, we are always happy to answer any questions you have. 

Furthermore, any advice we do give comes free of charge and under “no obligation”. 

CALL NOW: 01217739129

Or

EMAIL: sales@tilinglogistics.co.uk

Alternatively, click here for the Technical Data Sheet (TDS) for Faber No Oil.

Why Tiling Logistics?

Here at Tiling Logistics, we are very passionate about surface care, so much so that members of our team have devoted over 15 years to it. This 15-years worth of first-hand experience has granted us a great understanding of stone and tile surface care. 

After this time, we have developed an understanding of the best tools, products and methods for any surface treatment. Due to this, we are sure to have the best advice for you regardless of whether you are working on a commercial, industrial or domestic property.