Enquire Today
Free UK delivery
Express delivery available
+44(0) 121 773 9129
For any queries
Contact Us

Installing and Sealing Marrakech Cement Tiles

Step 1 – Fixing / Setting the tiles

Since the tiles are hand-made and therefore subject to color variations we recommend that you batch mix them randomly from different boxes when laying them out in order to balance color and tone variation to achieve the best overall aesthetic appearance.
Make sure that the surface that is to be tiled is prepared correctly regarding level, cleanliness, appropriate priming and perfectly dry.
Before laying the tiles ensure they are free of dust and any loose particles by wiping with a damp sponge.  The biscuit / rear of the tile should be pre-wet prior to fixing / setting. This can be easily achieved using a spray bottle set to mist or spray.
Installation of cement tiles requires back buttering / a double spread of adhesive. Use adhesive / thin-set mortar and a notched trowel and apply the adhesive / thin-set both to the substrate and to the back of the tile ensuring a 100% even coverage. (Under no circumstances attempt a "Dot & Dab Method")
The pattern of the tiles looks best with small grout joints (1-3 mm);  In some countries building regulations / insurance company policies require wider joints e.g. in wet areas – please check local regulation before installation. Wider joints may also be necessary when using under floor heating mats or cables.
When installing press the tiles down firmly into place and set level by hand only – do NOT use a hammer or rubber mallet since this may crack the tiles.
Work in small areas at a time, working clean and avoid getting the adhesive / thin-set on to the surface of the tile as this will result in staining the unsealed tiles – wipe off any excess adhesive / thin-set or other dirt immediately so as to avoid it  curing / setting on the porous surface.
Once the tiles are fixed / set allow to stand until the surface of the tiles is dry. Wipe off any dust or dirt before proceeding to Step 3. The tiles need to be clean and dry before sealing.

Step 2 – Sealing.

Please note that the first coat of sealer must to be applied before grouting, otherwise grout can penetrate the porous surface of these tiles.
The tiles have to be sealed in order to protect them from water and dirt and to give a reaction time.  You have an option to either maintain the original look or to enhance the appearance to produce a wet look.

Natural Appearance

We have found Miracle 511 H2O Plus to be particularly efficient and easy to use – see www.miraclesealants.com (in Sweden www.mpdiy.com). Follow the instructions on the container. While protecting against dirt and staining as well as giving you a reaction time to wipe up any spills this sealer will maintain the original look of the tile.

Enhanced Wet Look

To see if you want a enhanced look we recommend you wipe the face of the tile with a damp cloth or sponge to emulate the enhanced look.  The water will naturally dry out but it is extremely difficult to remove enhancing penetrating sealers if you decide you are unhappy with the appearance.  If after the test you decide want an enhanced and somewhat darker wet look finish we instead recommend you to use Miracle 511 Seal and Enhance.
Be aware that sealing in itself does not prevent excess grout (see step 3 – grouting) from sticking to the surface. It is thus of paramount importance that any excess grout on the surface of the tile is wiped off immediately  and meticulously after grouting.
Step 3 – Grouting.

Before grouting,  tiles should be allowed to dry for at least 24 hours. 
Mix the grout to strictly according to the manufacturer's instructions in order to facilitate applying to small grout joints (1-3 mm). Apply the grout to small areas at a time so that any excess grout on the face of the tiles can be wiped off immediately. Use a Micro fibre cloth / sponge or soft Scotch-Brite pad if necessary.
We advise against using very dark colored grout with pale tiles and vice versa.
Step 4 - After Grouting

Once the grout has dried a second coat of sealer should be applied to offer maximum protection paying particular attention to the grout itself.

Step 5 – After treatment

Once the tiles are dry we recommend an after treatment with Miracle Stone Soap.

Step 6 - Ongoing Maintenance & Cleaning

The tiles should be cleaned regularly using a pH Neutral cleaner such as Miracle Tile & Stone Cleaner (diluted stone soap if available in your market) . Repeated cleaning with stone soap will also help maintain a satin finish to the tiles and to an extent acts as a continuous topical / surface sealant of the tiles.
Depending on the amount of foot traffic and the type of sealer used the tiles may  have to be re-sealed periodically with a penetrating sealer.
Never use acidic cleaners or other acids on cement tiles.

Outdoor use

Tiles can be installed outdoors but there are special considerations. Please consult Marrakech Design prior to purchasing tiles with this aim.

Complaints and claims

Inspect your tiles prior to installation. No returns or claims will be accepted once the tiles have been fixed / installed.  Please note that Marrakech Design will never assume any responsibility for faulty workmanship.

These instructions / guide to installation are intended to provide helpful advice and guidance only.  Any advice, opinion or recommendations given in this report are given on the understanding that  neither the author, Tiling Logistics Limited or Marrakech Design shall not be liable either in law or in tort, for any damage or problem arising out of the use or misuse of such advice, opinion or recommendations.  In all cases local building regulations should be checked prior to installation.

Add Comment